How To Remove A Pur Water Filter From Faucet

Download Article

PUR has multiple products available for filtering h2o, but the filters become less effective over time as they fill with contaminants. How yous replace the filter depends on which system you're using. If you accept a plastic pitcher or dispenser you keep in the fridge, soak the new filter before screwing it in. For filtration systems that attach to your sink faucet, only remove the old filter and then you can put the new one in its place. When you're finished, yous'll have make clean h2o to drink for some other few months!

ane
Soak the replacement filter in cold water for 15 minutes. Place the new filter in a clean container that'due south deep enough so you tin can fully submerge it. Fill the container with cold water and exit information technology alone for at least 15 minutes. During this time, whatsoever excess carbon from the filter volition elevator out and split so information technology doesn't get in your drinking water.^[1]
- Soaking the filter besides ensures that water flows evenly when you use it.
- Don't employ water warmer than 86 °F (xxx °C) since it could damage the filter.
Warning: Avoid using 3rd-political party filters with your PUR pitcher or dispenser since they may not fit as well or take been tested as efficiently.
2
Twist the old filter counterclockwise to remove it. Accept the lid off of the pitcher or dispenser and set it aside. Then, elevator upwardly the pour tray, which is the blueish plastic reservoir on top, and have it out. Grab the cylindrical filter from the lesser and rotate it counterclockwise so it unhooks from the filter. Pull the old filter out through the top of the cascade tray and throw in the garbage.^[2]
- Look until the pour tray is empty to change your filter, or else information technology may be difficult to remove or you may spill.
Advertisement
3
Rinse the new filter nether your faucet for ten seconds. Take the filter out of the container when it'due south finished soaking and concur information technology underneath your faucet. Turn on common cold water and rotate the filter so you can rinse information technology off completely. Afterward 10 seconds, turn off the water and shake out whatever excess that's still in the filter.^[three]
- Don't utilise hot water to rinse the filter off, or else y'all may impairment it.
4
Screw the filter clockwise into the pour tray to secure it. Slide the long, cylindrical role of the filter through the hole in the middle of the cascade tray and button it downwards as far as it goes. Concur the filter past the bottom and rotate it clockwise until you hear it click into identify. Try borer on the end of the filter to make sure it doesn't pop out from the pour tray. Place the pour tray back into the bullpen or dispenser before replacing the lid.^[4]
- If the filter does pop out of the cascade tray, then you didn't properly secure it. Reinsert it and try turning information technology clockwise again.
- PUR filters for pitchers and dispensers normally work for 40 gallons (150 50), or approximately 2 months.
v
Hold the Reset push button down for 5 seconds if your pitcher or dispenser has i. Some newer PUR pitchers and dispensers have sensors that discover when yous need to replace the filter. Right after you replace the filter, press the Reset push on the lid and proceed information technology held down for five seconds. A dark-green light will blink on the lid in one case the sensor resets.^[5]
- Older pitchers or dispensers may not have an electronic display.
Advertisement

one
Unscrew the filtration system from your faucet. Support the weight of the filtration arrangement with your nondominant hand so information technology doesn't fall and break. Rotate the plastic locking nut holding the filtration system to the faucet counterclockwise to loosen it. Once y'all unscrew the system completely, carefully elevator it abroad from the faucet and fix it downward on a countertop or towel.^[6]
- Water may spill out from the faucet when you unscrew the filtration arrangement.
- Some models of PUR filtration systems may snap onto the faucet. If it doesn't unscrew, try pulling it straight downward from the faucet.
2
Twist open the top cover of the organisation to remove the old filter. Hold the filtration arrangement and so the rounded end of the large cylinder points upwardly. Unscrew the peak from the cylinder by rotating it counterclockwise, and set the encompass aside. Pull the old filter straight out from the system and throw it away in your trash.^[7]
- The top embrace is always on the opposite end of the spout that dispenses h2o.
3

Set the new filter inside of the system and spiral on the cover. Make sure the narrower end of the filter is on the lesser and the logo is right-side upwardly. Place the filter into the filtration system and so it has a loose fit. Set the peak cover dorsum over the filter and screw it into identify to secure it.^[8]
iv
Reattach the filtration system to your faucet. Agree the filtration system against the bottom of the faucet so the threadings are perfectly horizontal, or else they won't class a tight seal. Rotate the locking nut clockwise onto the faucet and go on tightening information technology until it's mitt-tight. Plow on the water and brand sure it doesn't drip or leak at the seam.^[ix]
- If your filtration system doesn't screw on, line it up with the faucet and apply firm pressure level to snap it on.
five
Run cold water through the filtration organization for five minutes. Plow the handle on the right side of the filtration system to divert the water through the filter. Permit the water to run through the filter for five minutes to get rid of any balance inside so it works more than efficiently. After that, you tin use the filter immediately after turning it on.^[x]
- PUR faucet filters work for 100 gallons (380 L) of water, or virtually iii months of use.
- Don't run h2o over 100 °F (38 °C) through the filter since you could damage it.
Warning: The water may sputter or look cloudy when y'all first utilise the new filter, but it will become better as you lot run water through it.

Advertisement

Enquire a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertizement

Many PUR filtration systems have electronic lights that detect when yous need to change your filter. If y'all come across a green light flash, y'all don't demand to modify your filter. If it blinks yellow or ruby-red, so you need to supersede the filter shortly.^[eleven]

Thanks for submitting a tip for review!

Advertizing

Don't utilise h2o that's above 82 °F (28 °C) in a pitcher or over 100 °F (38 °C) through a faucet since it can damage the filter.^[12]
Only use the filter with water that's already safe to drink since information technology volition not remove bacteria or infection.^[thirteen]